Ride On John Deere S100

Additional Information

OPERATOR’S SEAT
Fuel tank gauge
Convenient fuel-filler opening
The fuel tank gauge shows how much fuel is in the tank and can be seen without leaving the operator’s seat:Easy to check fuel level
Convenient location
Fuel tank:The capacity is 9.1 L (2.4 U.S. gal.)
The fuel-filler opening is conveniently located under the seat.Filling the tank without spilling is easy.
A tethered fuel tank cap is more convenient.
The sealed fuel cap helps keep vapors inside the tank.
The tractor has a California Air Resources Board (CARB) certified engine for reduced air pollution.
Frame made of full-length welded steel for reliability
Solid one-piece frame
Solid one-piece frame
The solid one-piece frame is constructed of 12-gauge, 2.66-mm (0.105-in.) steel:Full-length, robotically-welded frame design has high-strength steel rails for added strength and long life.
One-piece, steel fender deck is bolted to the frame.
CAST-IRON FRONT AXLE WILL NOT BEND
Front axle and wheel spindle
The front axle is constructed of solid cast iron that will not bend:Automotive-like steering system with sector and pinion steering gears and single drag link with a tie rod provides a very strong, low-effort, and tight-turning system.
Three grease fittings, on both steering spindles and center pivot, allow for regular lubrication to help maintain easy steering and minimize wear.
Large, 1.9-cm (0.75-in.) diameter wheel spindles provide excellent durability.
CARGO MOUNT™ SYSTEM MAKES INSTALLATION OF REAR BAGGER AND OTHER ATTACHMENTS EASY
Front CargO Mount points
Rear bagger is mounted with CargO Mount points
The CargO Mount system is a combination of front- and rear-mounting points providing convenient and easy installation of the sun canopy, rear bagger, and other attachments.
Automatic transmission makes it easy to choose the exact travel speed for each operating condition
E100 Tractor
The automatic transmission allows the operator to easily choose the desired forward or reverse travel speed by simply depressing a single foot pedal; this is similar to the way the driver of an automobile with automatic transmission changes speed when depressing the accelerator. Whether a slow speed for trimming or faster speed for open-area mowing is desired, the operator can easily adjust by how far the foot pedal is depressed. Brake pedal
Automatic transmission forward/reverse shift lever
With the brake pedal depressed and the forward/reverse lever in the center position, the engine can be started. Once the engine is started, it is not necessary to use the brake pedal when selecting forward or reverse. Simply move the forward/reverse lever to select travel direction, and then press the automatic foot pedal to choose from an infinite number of travel speeds. Speed control pedal
Operator foot depressing speed control pedal
With the automatic speed control pedal, the operator can choose from an infinite number of speeds forward or reverse:Forward: 0 to 8.9 km/h (0 to 5.5 mph)
Reverse: 0 to 5.1 km/h (0 to 3.2 mph)
Operator station designed for comfortable operation
Comfortable operator station, right side
Comfortable operator station, left side
The operator station is designed for operator comfort and easy operation:Controls are positioned where they are easy to reach and easy to use to control the tractor.
Steering wheel is positioned and angled to give the operator plenty of room and steering comfort.
Seat is tilted back at the optimum angle to provide the most comfortable operator position.
Steering wheel and dash
Wide footrest with debris channels
Controls are easy to see and use:Large, three-spoke steering wheel for greater operator comfort and control
Ignition switch is on the dash for starting ease
Wide footrest areas with non-slip, anti-vibration floor mats are provided for operator comfort:Footrest area is designed for optimum operator comfort
Debris-removing channels help keep the footrest area clean and dry
Comfortable seat
Easily-adjusted seat and beverage holder
The operator station is designed for operator comfort and easy operation:Controls are positioned where they are easy to reach and easy to use to control the tractor.
Steering wheel is positioned and angled to give the operator plenty of room and steering comfort.
Seat is tilted back at the optimum angle to provide the most comfortable operator position.
Seat springs give a smoother ride
Two long seat springs give plenty of seat travel to smooth out the ride, keeping the operator comfortable while operating the tractor. Seat can be tilted forward for protection from the elements and to provide easy access to the fuel tank.
Instruments and controls are easy to find and convenient to use
E100 Tractor mowing
Steering wheel and controls